(SKU:RB-02S088)電流檢測傳感器
來自ALSROBOT WiKi
目錄 |
產品概述
此產品由一個電流感應器TA12-200組成構成??梢詫⒋蟮碾娏髁哭D(zhuǎn)換為幅度小的電壓量輸出。該模塊采用沉金工藝,外觀更加美觀,同時采用防插反3Pin接口,操作更加安全,插口一邊有大寫字母A表示該模塊位模擬量傳感器,另一邊是電流表的圖標標志表示該模塊具有測試電流的功能。此產品可以應用于交流電的電流檢測,最大可檢測的電流為5A。
規格參數
- 工作電壓 :+5v
- 尺寸大?。?30mm x 25mm
- 重量大小:8g
- 信號類型:模擬信號
- 孔徑:4.96mm
接口定義
- S:信號引腳
- NC:不需要連接
- -:電源地
使用方法
使用硬件
- 振動馬達 * 1個
- 電位計模塊 * 1個
- 電流傳感器 * 1個
- Carduino UNO 控制器 * 1個
- 傳感器擴展板 V5.0 * 1個
- 杜邦線 * 若干
接線示意圖
引腳接線:
傳感器引腳 | 所接引腳 |
電位計模塊 S 引腳 | 穿過電流傳感器接在UNO的D13 S 引腳 |
電位計模塊 + 引腳 | 振動馬達 + 引腳 |
電位計模塊 - 引腳 | 懸空 |
電流傳感器 | 控制器 A0 引腳 |
振動馬達 + — 引腳 | 分別接在控制器Vcc和GND |
注:NC可以不接
例子程序
#define ELECTRICITY_SENSOR A0 int mada = 13; float amplitude_current; float effective_value; void setup() { Serial.begin(9600); pins_init(); pinMode(mada, OUTPUT); } void loop() { digitalWrite(mada, HIGH); int sensor_max; sensor_max = getMaxValue(); Serial.print("sensor_max = "); Serial.println(sensor_max); //the VCC on the RobotBase interface of the sensor is 5v amplitude_current=(float)sensor_max/1024*5/800*2000000; effective_value=amplitude_current/1.414;//minimum_current=1/1024*5/800*2000000/1.414=8.6(mA) Serial.println("The amplitude of the current is(in mA)"); Serial.println(amplitude_current,1);//Only one number after the decimal point Serial.println("The effective value of the current is(in mA)"); Serial.println(effective_value,1); } void pins_init() { pinMode(ELECTRICITY_SENSOR, INPUT); } /*Function: Sample for 1000ms and get the maximum value from the SIG pin*/ int getMaxValue() { int sensorValue; //value read from the sensor int sensorMax = 0; uint32_t start_time = millis(); while((millis()-start_time) < 1000)//sample for 1000ms { sensorValue = analogRead(ELECTRICITY_SENSOR); if (sensorValue > sensorMax) { /*record the maximum sensor value*/ sensorMax = sensorValue; } } return sensorMax; }
程序效果
打開串口監視器之后,會顯示出當前檢測到的電流值。
產品相關推薦
購買地址
周邊產品推薦
Arduino 旋轉角度傳感器
通用傳感器連接線 3P杜邦連接線